Hey everyone, it’s Jake from the metal cable glands team—before you ask, yes, I’ve fielded this exact question a dozen times in the last month alone from folks in automotive assembly lines, oil and gas refineries, even some small-scale foundries testing new equipment. The short answer? It depends on which metal cable glands you use, how you spec them, and if you’re pairing them with the right supplementary parts for your specific heat load. The long answer is where the real value is, so let’s dive in without the engineering jargon that makes your eyes glaze over. Metal Cable Glands

First, let’s talk about why this question matters so much right now. In 2024, we’ve seen a huge uptick in projects moving into extreme heat environments—think desert-based solar farms running 12-hour days at 140°F, or manufacturing lines where furnaces and stoves raise ambient temps to 180°F in the machinery bay. A standard plastic cable gland would melt, warp, or secrete toxic gasses under those conditions, which is why more teams are turning to metal alternatives. But not all metal cable glands are created equal, and that’s where I see most people slipping up.
Let’s break down the metals we work with most at our facility: brass, stainless steel, and aluminum. Each behaves totally differently when the temperature climbs, and each has a sweet spot for hot environments. Brass is the workhorse, right? It’s affordable, easy to machine, and has a melting point around 1,650°F. Wait, that sounds like a lot—why isn’t brass the go-to for every heat application? Because brass expands way more than stainless steel. You have to account for thermal expansion, or you’ll end up with gaps between the gland, the cable, and the enclosure. If there’s even a tiny gap, you lose the IP rating (ingress protection—think dust, water, debris) that the gland is supposed to provide, and worst case, moisture or dust gets in and causes a short circuit in a control panel. That’s a huge headache no one needs.
Stainless steel is the star of the show for hot environments. 316L stainless steel, specifically. It has a melting point near 2,600°F, and its thermal expansion rate is almost 50% lower than brass, which means it holds its shape even when temps jump from 70°F to 200°F in an hour. We tested a batch of our 316L stainless steel cable glands last year in partnership with a wind turbine company that installs their gear on mountain tops where summer temps reach 170°F and winter drops to -40°F. After 12 months of use, when they pulled one gland for inspection, there was zero warping, zero gaps, and the IP68 rating was still intact. That’s the kind of performance we aim for. Don’t mistake 304 stainless steel for 316L, though—304 has a much lower melting point, around 2,500°F, and it’s more prone to corrosion in high-heat, high-humidity environments like coastal refineries. I’ve seen teams grab 304 by mistake and end up replacing glands twice a year, which adds up fast.
Aluminum is a third option, and it’s lighter than both brass and stainless steel, with a melting point around 1,220°F. That sounds low, but it’s actually perfect for mid-heat applications—think food processing plants where ambient temps hit 120°F near ovens, or commercial HVAC systems. Aluminum’s thermal expansion is on par with brass, so you still need to pair it with a high-quality sealing element that can flex with the movement, but it’s a great budget pick for environments that aren’t pushing 200°F+.
Now, the part no one tells you: the temperature rating of a metal cable gland isn’t just about the metal itself. It’s also about the gasket and sealing material inside. Most people only ask for metal glands and forget that the rubber or plastic seal is what actually keeps out elements and grips the cable. Silicone gaskets? They can handle up to 450°F, which is way higher than the melting point of most metal glands. Neoprene? That maxes out around 200°F, so if you’re running at 250°F, a neoprene seal will harden, crack, and fail long before the brass or stainless steel does. We always make a point to ask customers what temperature their enclosure runs at, so we can recommend the right seal—silicone for extreme heat, EPDM for mid-range heat and outdoor use, even high-temperature Viton for applications near furnaces where temps hit 500°F. Viton is a game-changer for those super hot spots; it’s flexible up to 400°F and stable up to 500°F, so it won’t break down when exposed to radiant heat.
I also want to talk about misapplication, because that’s where most failures happen. Last year, a customer from a mining operation came to us with a problem: their metal cable glands were failing within three months in a new ore processing line. They were using brass glands, and the ambient temp in the line was averaging 220°F, with spikes up to 250°F. We looked at their setup and saw they were using neoprene seals, which we already knew isn’t rated for that heat, but also—they were overtightening the glands to compensate for thermal expansion. Overtightening a metal cable gland can crush the cable’s insulation, especially if it’s a thin or flexible cable, leading to insulation degradation over time. We switched them to 316L stainless steel glands with silicone seals, adjusted their tightening torque to the manufacturer’s spec, and after six months, they haven’t had a single failure. That’s the kind of solution we love to deliver.
Another common question: what about extreme radiant heat, like near a furnace or a kiln? Metal cable glands that are exposed to direct radiant heat (not just ambient temp) need extra consideration. Even if a 316L stainless steel gland can handle 2,600°F, the seal can’t. So for those applications, we recommend glands that are designed with a heat shield or using mineral-based sealing materials, not rubber. We’ve had custom orders for kiln control systems where we use metal glands with compressed asbestos-free mineral seals, which can handle direct radiant heat up to 1,200°F, way higher than rubber seals. It’s not a one-size-fits-all solution, which is why we take the time to ask customers about their specific environment, not just “what’s your temperature?”
Wait, let’s address a myth I hear all the time: metal is always better for heat. That’s not true. For temperatures under 180°F, plastic cable glands are perfectly fine, lighter, cheaper, and easy to install. But once you climb above 180°F, plastic will start to lose its structural integrity, outgassing, warping, or failing to provide the required IP rating. We’ve tested plastic glands in a 200°F oven and had one melt completely in just two hours, while a 316L stainless steel gland sitting right next to it showed no change. That’s a clear difference, and it’s why we only recommend metal glands for high-heat applications.
Now, let’s get to maintenance, because even the best metal cable glands won’t last if you don’t take care of them. In hot environments, metal expands and contracts more often than in moderate temps, so you should inspect glands every six months, not every year. Check for gaps between the gland and the enclosure, cracks in the seal, or signs of corrosion (especially in high-heat, salty environments like coastal power plants). We also recommend retorquening glands once a year after the initial installation, to account for any minor shifting from thermal expansion. It’s a small step, but it prevents a lot of avoidable failures.
At the end of the day, the answer to “can metal cable glands be used in hot temperatures?” is a resounding yes—if you spec the right type of metal, the right seal, and install and maintain them correctly. We’ve supplied metal cable glands to projects across industries, from solar farms in Arizona to refineries in Texas, and the most successful partnerships are the ones where we don’t just send a product, we work with the customer to make sure it fits their specific needs.
If you’re working on a project that involves high temperatures, and you’re not sure which metal cable glands are right for you, or you’ve had issues with failing glands in the past, we’re here to help. We can walk you through material specs, seal options, torque requirements, and anything else you need to make sure your setup works reliably, no matter how hot it gets.

Reach out to our team to discuss your project details and find the right solution for your application.
Custom Nylon Cable Ties References
- International Electrotechnical Commission (IEC) 62444: Cable Glands, Joints and Accessories for Electrical Equipment
- ASME Boiler and Pressure Vessel Code (BPVC) Section II: Material Specifications
- DuPont Viton Fluoroelastomer Technical Data Sheet, 2023 Edition
- NEMA Standard 250: Ingress Protection (IP) Ratings for Enclosures, 2022 Revision
- Copper Development Association: Thermal Properties of Brass Alloys for Industrial Applications, 2021
Hangzhou Gordon Electric Co., Ltd.
Hangzhou Gordon Electric Co., Ltd. is well-known as one of the leading metal cable glands manufacturers and suppliers in China. We warmly welcome you to wholesale high quality metal cable glands at competitive price from our factory. For custom service, contact us now.
Address: No.173 Xingqiao North Road, Yuhang District, Hangzhou, Zhejiang 31100, China
E-mail: jeson@gordon-elec.com
WebSite: https://www.gordon-elec.com/